Makerfire Armor 65 Lite
Flight controller: Tiny Lite Silverware FC
Remote： Tiny lite RC
Motor ： 7×16mm 17600KV（firstname.lastname@example.orgV）
Propeller： 4-Blade 31mm
VTX ： 5.8G/40CH/25mW
Camera ： 800TVL/120°
Battery： 300mAh /3.8V/1S/30C/Li-HV
Flight time: 4min20second
Remote Distance: 100 meters
RC Gestures Setting (Mode2)
- Left - Left - Down: acro mode
- Right - Right - Down : level mode
- Up - Down - Up: Cycle pid term to the next ( P - I - D )
- Up - Down - Down: Cycle pid axis to be changed ( Roll/Pitch - Yaw )
- Up - Down - Left: Decrease the selected value
- Up - Down - Right: Increase the selected value
- Down - Down - Down: Accelerometer calibration / Save pids if changed
The 25mW/40CH AIO camera in Armor65 lite is characterized by wide dynamic,
high-definition, wide angle and no delay.The light and mini AIO camera
supports button and frequency choice as well as NTSC/PAL TV system.
The LED will show video transmiter frequency,8 LEDS indicates the signal
channel, 6LEDS indicates the frequencey,the specific frequency will base
on the video trasnmitter frequency chart.
Long Press can switch over the NTSC/PAL TV system.
Short Press can switch over the vertical inverted image.
Long Press can switch the frequency of the Video transmitter.
Short Press can switch over the specific signal channel of currecnt frequency.
Finish frequency operation to configure automatically frequency point and groups. It also is equipped with non-volatile memory function.
Armor65 Lite radio transmitter
The toys like JJRC H67, Eachine E011 etc use the Bayang protocol radio transmitters.
Jumper T8SG radio transmitter
MTX-9D multiprotocol module (Suitable for Frsky Tanaris QX7 X9D X9D Plus X12S, Flysky TH9X, Turnigy 9XR/9XR PRO)
Other 4in1 multiprotocol module that support the Bayang protocol.
If not sure whether your radio transmitter could support this FC board, please email us (Support@makerfire.com) for help.
For example, if you have a Frsky Tanaris QX7 / X9D radio transmitter and want to try this FC board,
just plug in a MTX90 multiprotocol module.
Remote control configuration
1)Bayang protocol remote control configuration
Power up the Armor65 Lite, the FC indicator LED flashes slowly for 6 times and then turnes into fast flash mode. The fast flash mode shows the beginning of the binding mode.
There is the "di" sound in the buzzer when turn on the radio transmitter and then turn into the binding mode automatically.
After finishing the binding, the FC indicator LED fashes solid,and the radio transmitter has the "di" sound.
After finishing the binding, turn off the radio transmitter, the FC indicator LED turns into slowly flash mode.
Turn on the radio transmitter before power up the Armor65 Lite, then the binding fails.
When Changing the new battery needs binding again.
2）Take Frsky X9D as an example
Install the MTX9D module in Frsky X9D radio transmitter in the correct place.
Turn on the radio transmitter,and create a radio transmitter mode.
In MODEL SETUP setting page,Set “Internal RF”to " OFF" and “External RF”to "PPM".
Turn off the radio transmitter.
Power up the Armor65 lite RTF and wait for the binding mode.
When the The indicator LED flashes fast,turn on the radio transmitter and push the right-Throttle to top-right direction.
The indicator LED turning the fast flash into solid shows binding is successfully.
3）T8SG remote control
Power up the Armor65 Lite, the FC indicator LED flashes slowly for 6 times and then turn into fast flash mode. The fast flash mode shows the beginning of the binding mode.
Turn on the radio transmitter, short press "ENT" and go into "“Main menu", press " ENT", go into "Model menu",choose "“Model Setup”page.
By default,the photo show below for your reference.
Adjust the cursor into "PPM In",set the receiver to "Bayang" and choose " Re-Init”.
Press "ENT" and enter the binding mode.The indicator LED turning the fast flash into solid shows binding is successfully.
The T8SG enters the binding mode automatically if setting has been finished in advance.
There is the "did" sound at the starting and finishing binding mode.
4)Other radio transmitter
CH2: ELE (PITCH)
CH3: THR (THROTTLE)
1 . Charge the battery in time when low voltage.
2 . Turn the USB charger into 4.35v before charging.
3 . The solid red light shows the battery is in charging,light off shows in full charge.
Armor65 Lite RTF （Silverware Firmware）
1× Armor65 Lite RTF
1× Radio Transmitter
1× 300mAh 1S 3.8V Battery
1× One-way 4.35V Charger
1× Propeller Tool
1× Service Card
3 x Sticker
How to Flash Firmware for Lite FC
The only method to restore the factory PID is reflashing the firmware for the moment.
About how to flash the firmware, please check on Silverware offical website or RCG.
The firmware for Makerfire TinyLite FC board is available in the attached file.
If You want to compile the files by yourself, please download the files here:
Silverware is an open-source flight controller firmware developed by GitHub user silver13 for the H8 mini, BWhoop B03, and Eachine E011/E011C FCs. It was forked and further refined by GitHub user NotFastEnuf
Silverware is a firmware for some micro quadcopters, especially the whoop FPV racing.
Silverware supports level mode and acro mode. Also it can change the the settings for custom builds, or to adapt to personal preferences.
By default, Silverware changes modes, tune PIDs, calibrate accelerometer or save settings by stick sequences(also called gestures).
For example, the Frsky QX7 radio transmitter switches the FC's mode between level and acro by moving the right stick as show below.
Any questions,please contact us.
Find us on social media：facebook